In brief: Most failed or unrepeatable fogging results come from the workflow, not the material. Contaminated glass or foil, unstable bath or cooling-plate temperature, poor sealing and uncontrolled conditioning account for most out-of-range reference checks and scattered results between runs.
Why fogging tests fail
A fogging test looks simple: heat a specimen, collect what condenses on a cooled surface, then measure it. In practice, the deposit being measured is often a few milligrams or a thin optical film. Small errors in cleaning, temperature or handling can shift that result more than the material itself does.
For Indian Tier 1 and Tier 2 suppliers, the cost is real. A failed reference run means a repeat test, a delayed PPAP submission, or a material wrongly rejected. This guide covers the ten causes we see most often in automotive labs and how to correct each one. If you are still choosing between methods, start with our guide to the gloss, gravimetric and haze methods.
Quick diagnosis: symptom, cause, fix
| Symptom | Most likely cause | First fix to try |
|---|---|---|
| Reflectometric reference value below range | Dirty or scratched glass plate; residue on beaker | Re-clean glass with the specified procedure; replace scratched plates |
| Gravimetric value higher than expected | Foil contamination or moisture pickup before weighing | Handle foil with tweezers and gloves; desiccate before weighing |
| Gravimetric value lower than expected | Leaking seal; cooling plate too warm | Inspect seal rings; verify cooling-plate temperature |
| Large spread between beakers in one run | Uneven bath temperature or immersion depth | Check bath uniformity at every position; top up the heat-transfer fluid |
| Results drift from week to week | Uncalibrated sensors or ageing bath fluid | Calibrate temperature sensors; replace degraded fluid |
| Good reference run, scattered sample results | Specimen preparation or conditioning varies | Standardise cutting, orientation and pre-conditioning |
| Haze readings unstable | Measuring before the plate stabilises | Follow the conditioning interval exactly before reading |
10 common causes of fogging test failure
1. Contaminated glass plates
The reflectometric and haze methods measure a very thin film, so any fingerprint, detergent residue or dust becomes part of the result. Clean plates with the exact procedure in your controlled standard, rinse thoroughly, and store them covered. Retire plates with scratches or etching, because a damaged surface scatters light before the test even starts.
2. Aluminium foil handling and moisture
In the gravimetric method, the result is often only a few milligrams. A skin oil trace or absorbed moisture can be the same order of magnitude. Handle foil only with clean tweezers and gloves, and condition it in a desiccator before both weighings, as DIN 75201 and ISO 6452 require.
3. Bath temperature drift or poor uniformity
Most fogging methods heat the beakers to around 100 °C. If the bath is a degree or two off at some positions, beakers in the same run produce different results. Map the temperature at every beaker position, not just at the controller sensor, and recheck after any fluid top-up.
4. Cooling plate temperature
The cooling plate (typically 21 °C) controls how much vapour condenses. A warm plate collects less, which makes a material look better than it is. Verify the circulating chiller setpoint and the actual plate temperature with an independent probe.
5. Leaking seals
Worn, hardened or misaligned fluoroelastomer seal rings let vapour escape instead of condensing on the collector. This usually shows up as low gravimetric values. Inspect seals before each run and replace them on a fixed schedule.
6. Wrong immersion depth or low bath fluid
The beaker must be immersed to the depth the standard specifies. As heat-transfer fluid evaporates or degrades, the effective heating of the specimen changes. Check the level before every run and replace fluid that has darkened or thickened.
7. Inconsistent specimen preparation
Specimen diameter, thickness, exposed face and orientation all affect emission. Use a calibrated die cutter, keep the exposed face up as specified, and record the material lot. Pre-condition all specimens identically before testing.
8. Uncontrolled conditioning after the test
Most standards require the fogged glass or foil to be conditioned at around 23 °C and 50 % RH, away from draughts and sunlight. Condensed water on the collector evaporates at different rates if the room is not controlled. Measure only after the full conditioning interval, and log room conditions with each result.
9. Measuring instrument errors
An uncalibrated gloss meter, haze meter or analytical balance turns a good test into a bad number. Calibrate gloss and haze meters against their reference standards, and use a balance with resolution suited to milligram-level deposits, placed on a stable, draught-free bench.
10. Mixing standards, editions or OEM specs
DIN 75201, ISO 6452, SAE J1756 and OEM methods such as VW PV 3015, PV 3920 and GMW 3235 differ in detail. Running a sample to one document and reporting against another causes avoidable disputes. Keep a method matrix per customer that records the standard, edition, method, conditioning and acceptance limit.
Use a reference run to find the problem
A reference-material run is the fastest way to tell an instrument or workflow problem from a material problem. DIN 75201 and ISO 6452 describe a check using a known plasticiser in place of the specimen: DIDP for the reflectometric method and DOP for the gravimetric method, each with a target window.
- Reference in range, samples scattered: the instrument is fine. Look at specimen preparation, conditioning and handling (causes 7 and 8).
- Reference out of range: stop testing samples. Work through glass or foil cleanliness, temperatures, seals and immersion (causes 1 to 6) before re-running.
- Reference passes some days, fails others: suspect room conditions, fluid ageing or sensor drift (causes 3, 6, 8 and 9).
The exact reference quantity, conditions and acceptance window depend on the standard edition. Always take them from your controlled copy, and run the reference at the frequency your quality system or customer requires. Note that haze methods often have no equivalent reference check, so plate cleanliness and meter calibration matter even more there.
Pre-test checklist for fogging labs
Print this and keep it next to the fogging tester.
- Standard, edition and method confirmed against the customer requirement
- Glass plates cleaned, inspected for scratches and stored covered
- Aluminium foil cut, desiccated and pre-weighed using tweezers
- Bath fluid level and condition checked; temperature stable at every position
- Cooling-plate temperature verified with an independent probe
- Seal rings inspected; worn rings replaced
- Specimens cut to size, oriented correctly and pre-conditioned
- Conditioning room at the required temperature and humidity, no draughts or sunlight
- Gloss meter, haze meter or balance within calibration
- Reference run due? If yes, run it before samples
Frequently asked questions
Why are my fogging test results not repeatable?
The most common reasons are uneven bath temperature between beaker positions, inconsistent cleaning of glass or foil, and uncontrolled conditioning after the test. Run a reference-material check to see whether the instrument or the sample handling is the source.
Which fogging method is more repeatable, reflectometric or gravimetric?
Laboratory experience generally shows the gravimetric method is more forgiving, because it measures mass rather than an optical film that is sensitive to cleaning and conditioning. The method you use, however, must follow the customer specification.
How often should a fogging tester be calibrated?
Temperature sensors, the cooling system and the measuring instruments should be calibrated at least annually, or as your quality system requires. Reference-material runs are typically done more often, such as weekly or before each test batch.
Can a fogging test measure VOCs in a car cabin?
No. A fogging test measures how much condensable material a sample deposits under set conditions. Identifying individual compounds or total VOCs needs a separate analytical method.
What cooling-plate temperature is used in fogging tests?
Common methods use about 21 °C for the cooling plate and about 100 °C for the bath, but always confirm the values in your controlled standard or OEM specification.
Get repeatable fogging results
A stable instrument removes several of these causes at the source. The FT-F1 Automotive Fogging Tester supports reflectometric, gravimetric and haze workflows with controlled bath and cooling-plate temperatures.
Already running fogging tests and seeing failures? Flexitest's calibration and AMC teams can verify your setup on site. Share your standard, method and recent results with sales@flexitest.in or call +91 93263 25135 or +91 22-4970 6073.
Sources
- Labthink: three fogging test methods (calibration and conditioning notes)